MegaCli

http://hwraid.le-vert.net/wiki/LSIMegaRAIDSAS

http://wiki.hetzner.de/index.php/LSI_RAID_Controller/en

http://tools.rapidsoft.de/perc/perc-cheat-sheet.html

http://perso.ens-lyon.fr/kevin.reverchon/doku.php?id=start:sysadmin:zfs_dell

http://www.inquisitor.ru/doc/einarc/

Sur les R510dataX (en Sun Solaris), pour maniper sur les controleur raid, à chaud.

  • lister les disques et leurs état :
./MegaCli -PdList -aALL | grep alert
./MegaCli -pdlist -a0 | /usr/xpg4/bin/grep -e '^Enclosure Device ID:' -e '^Slot Number:' -e 'alert'

Caches, Battery + WriteBack

  • activation du ReadCache (Adapter)
./MegaCli -LDSetProp -Cached -LAll -aAll
  • activation du DiskCache (Disk)
./MegaCli -LDSetProp EnDskCache -LAll -aAll
  • activation du AdaptiveReadAhead (Adapter)
./MegaCli -LDSetProp ADRA -LALL -aALL
  • état des batteries
./MegaCli -AdpBbuCmd -GetBbuStatus -a0 | /usr/xpg4/bin/grep -e '^isSOHGood' -e '^Charger Status' -e '^Remaining Capacity'

./MegaCli -AdpBbuCmd -GetBbuStatus -a1 | /usr/xpg4/bin/grep -e '^isSOHGood' -e '^Charger Status' -e '^Remaining Capacity'

Si tout est good :

  • Activation du WB
./MegaCli -LDSetProp WB -LALL -aALL
  • mais désactivation automatique si la batterie devient bad
./MegaCli -LDSetProp NoCachedBadBBU -LALL -aALL
  • si on se fout de l'état des batteries (ZFS is COW)
./MegaCli -LDSetProp CachedBadBBU -LALL -aALL
  • activation du JBOD

:!: ne fonctionne pas sur les vraies cartes raid H700/710, H800/810 (dispo à partir de Hx30), fonctionne sur les H200/H210, H300/H310 et supérieures.

MegaCli -AdpSetProp -EnableJBOD -1 -aALL

Remplacer un disque HS

sur R510dataX

zpool scrub <pool>
  • Repérer le disque fautif
./MegaCli -pdlist -a0 | /usr/xpg4/bin/grep -e '^Enclosure Device ID:' -e '^Slot Number:' -e 'alert'
./MegaCli -PDInfo -PhysDrv\[32:11\] -a0
  • Éjecter le disque fautif
./MegaCli -PdPrpRmv -PhysDrv\[32:11\] -a0
./MegaCli -PDOffLine -PhysDrv\[32:11\] -a0
  • échanger physiquement les disques
  • effacer la config VD ou foreign du nouveau disque (si besoin)
#./MegaCli -PDMakeGood -PhysDrv \[32:11\] -a0 # si Unconfigured(bad)
./MegaCli -CfgForeign -Scan -a0
./MegaCli -CfgForeign -Clear -a0
#./MegaCli -PDClear -Start -PhysDrv\[32:11\] -a0 # si dans un raid > 0
  • trouver et purger le preserved cache
./MegaCli -AdpAllInfo -a0 -nolog | grep Preserved
./MegaCli -GetPreservedCacheList -a0
./MegaCli -DiscardPreservedCache -L13 -a0
  • créer un nouveau VD (raid0) avec le nouveau Physical Disk (Write Through)
./MegaCli -CfgLdAdd -r0 '[32:11]' -a0
                                     
Adapter 0: Created VD 13

Adapter 0: Configured the Adapter!!

Exit Code: 0x00
  • créer un nouveau disque d'accès direct (H200,H310,H730/830)
./MegaCli -PDMakeJBOD -PhysDrv[32:1] -a0
  • remettre les configs du VD au propre (cache, WB, readahead, etc)
./MegaCli -LDSetProp -Cached -LAll -aAll
./MegaCli -LDSetProp EnDskCache -LAll -aAll
./MegaCli -LDSetProp ADRA -LALL -aALL
./MegaCli -LDSetProp WB -LALL -aALL
./MegaCli -LDSetProp NoCachedBadBBU -LALL -aALL
  • prévenir zfs
zpool status
zpool replace data c0t6d0
zpool status

Un resilver du disque doit démarrer automatiquement.

Ref : http://docs.oracle.com/cd/E19253-01/819-5461/gbcet/index.html

MegaCli -help

MegaCli -v 
MegaCli -help|-h|? 
MegaCli -adpCount 
MegaCli -AdpSetProp {CacheFlushInterval -val} | { RebuildRate -val} 
    | {PatrolReadRate -val} | {BgiRate -val} | {CCRate -val} 
    | {ReconRate -val} | {SpinupDriveCount -val} | {SpinupDelay -val} 
    | {CoercionMode -val} | {ClusterEnable -val} | {PredFailPollInterval -val} 
    | {BatWarnDsbl -val} | {EccBucketSize -val} | {EccBucketLeakRate -val} 
    | {AbortCCOnError -val} | AlarmEnbl | AlarmDsbl | AlarmSilence 
    | {SMARTCpyBkEnbl -val} | {SSDSMARTCpyBkEnbl -val} | NCQEnbl | NCQDsbl 
    | {MaintainPdFailHistoryEnbl -val} | {RstrHotSpareOnInsert -val} 
    | {DisableOCR -val} | {BootWithPinnedCache -val} 
    | AutoEnhancedImportEnbl | AutoEnhancedImportDsbl 
    | {EnblSpinDownUnConfigDrvs -val}|{UseDiskActivityforLocate -val} -aN|-a0,1,2|-aALL 
    | {ExposeEnclDevicesEnbl -val} | {SpinDownTime -val} 
    | {SpinUpEncDrvCnt -val} | {SpinUpEncDelay -val} | {Perfmode -val} -aN|-a0,1,2|-aALL 
MegaCli -AdpSetProp -AutoDetectBackPlaneDsbl -val -aN|-a0,1,2|-aALL 
       val - 0=Enable Auto Detect of SGPIO and i2c SEP. 
             1=Disable Auto Detect of SGPIO. 
             2=Disable Auto Detect of i2c SEP. 
             3=Disable Auto Detect of SGPIO and i2c SEP. 
MegaCli -AdpSetProp -CopyBackDsbl -val -aN|-a0,1,2|-aALL 
       val - 0=Enable Copyback. 
             1=Disable Copyback.
MegaCli -AdpSetProp -EnableJBOD -val -aN|-a0,1,2|-aALL 
       val - 0=Disable JBOD mode. 
             1=Enable JBOD mode. 
MegaCli -AdpSetProp -DsblCacheBypass -val -aN|-a0,1,2|-aALL 
       val - 0=Enable Cache Bypass. 
             1=Disable Cache Bypass. 
MegaCli -AdpSetProp -LoadBalanceMode -val -aN|-a0,1,2|-aALL 
       val - 0=Auto Load balance mode. 
             1=Disable Load balance mode. 
MegaCli -AdpSetProp -UseFDEOnlyEncrypt -val -aN|-a0,1,2|-aALL 
       val - 0=FDE and controller encryption (if HW supports) is allowed. 
             1=Only support FDE encryption, disallow controller encryption. 
MegaCli -AdpSetProp -PrCorrectUncfgdAreas -val -aN|-a0,1,2|-aALL 
       val - 0= Correcting Media error during PR is disabled. 
             1=Correcting Media error during PR is allowed. 
MegaCli -AdpSetProp -DsblSpinDownHSP -val -aN|-a0,1,2|-aALL 
       val - 0= Spinning down the Hot Spare is enabled. 
             1=Spinning down the Hot Spare is disabled. 
MegaCli -AdpSetProp -DefaultLdPSPolicy -Automatic| -None | -Maximum| -MaximumWithoutCaching -aN|-a0,1,2|-aALL 
MegaCli -AdpSetProp -DisableLdPS -interval n1 -time n2 -aN|-a0,1,2|-aALL 
       where n1 is the number of hours beginning at time n2 
MegaCli -AdpSetProp -ENABLEEGHSP -val -aN|-a0,1,2|-aALL 
           val - 0= Disabled Emergency GHSP. 
                         1= Enabled Emergency GHSP. 
MegaCli -AdpSetProp -ENABLEEUG -val -aN|-a0,1,2|-aALL 
           val - 0= Disabled Emergency UG as Spare. 
                         1= Enabled Emergency UG as Spare. 
MegaCli -AdpSetProp -ENABLEESMARTER -val -aN|-a0,1,2|-aALL 
           val - 0= Disabled Emergancy Spare as Smarter. 
                         1= Enabled Emergancy Spare as Smarter. 
MegaCli -AdpSetProp -DPMenable -val -aN|-a0,1,2|-aALL 
       val - 0=Disable Drive Performance Monitoring . 
             1=Enable Drive Performance Monitoring. 
MegaCli -AdpSetProp -SupportSSDPatrolRead -val -aN|-a0,1,2|-aALL 
       val - 0=Disable Patrol read for SSD drives . 
             1=Enable Patrol read for SSD drives. 
MegaCli -AdpGetProp CacheFlushInterval | RebuildRate | PatrolReadRate
    | BgiRate | CCRate | ReconRate | SpinupDriveCount | SpinupDelay 
    | CoercionMode | ClusterEnable | PredFailPollInterval | BatWarnDsbl 
    | EccBucketSize | EccBucketLeakRate | EccBucketCount | AbortCCOnError 
    | AlarmDsply | SMARTCpyBkEnbl | SSDSMARTCpyBkEnbl | NCQDsply 
    | MaintainPdFailHistoryEnbl | RstrHotSpareOnInsert 
    | EnblSpinDownUnConfigDrvs  | DisableOCR 
    | BootWithPinnedCache | AutoEnhancedImportDsply | AutoDetectBackPlaneDsbl 
    | CopyBackDsbl | LoadBalanceMode | UseFDEOnlyEncrypt | WBSupport | EnableJBOD 
    | DsblCacheBypass | ExposeEnclDevicesEnbl | SpinDownTime | PrCorrectUncfgdAreas 
    | UseDiskActivityforLocate | ENABLEEGHSP | ENABLEEUG | ENABLEESMARTER | Perfmode | -DPMenable -aN|-a0,1,2|-aALL 
    | DefaultLdPSPolicy | DisableLdPsInterval | DisableLdPsTime | SpinUpEncDrvCnt 
    | SpinUpEncDelay | PrCorrectUncfgdAreas 
    | DsblSpinDownHSP | SupportSSDPatrolRead -aN|-a0,1,2|-aALL
MegaCli -AdpAllInfo -aN|-a0,1,2|-aALL  
MegaCli -AdpGetTime -aN|-a0,1,2|-aALL  
MegaCli -AdpSetTime yyyymmdd hh:mm:ss -aN   
MegaCli -AdpSetVerify -f fileName -aN|-a0,1,2|-aALL  
MegaCli -BBUMfgSet -f filename -aN|-a0,1,2|-aALL  
MegaCli -AdpBIOS -Enbl |-Dsbl | -SOE | -BE | EnblAutoSelectBootLd | DsblAutoSelectBootLd | -Dsply -aN|-a0,1,2|-aALL 
MegaCli -AdpBootDrive {-Set {-Lx | -physdrv[E0:S0]}}|-Get -aN|-a0,1,2|-aALL 
MegaCli -AdpAutoRbld -Enbl|-Dsbl|-Dsply -aN|-a0,1,2|-aALL
MegaCli -AdpCacheFlush -aN|-a0,1,2|-aALL
MegaCli -AdpPR -Dsbl|EnblAuto|EnblMan|Start|Suspend|Resume|Stop|Info|SSDPatrolReadEnbl |SSDPatrolReadDsbl  
         |{SetDelay Val}|{-SetStartTime yyyymmdd hh}|{maxConcurrentPD Val} -aN|-a0,1,2|-aALL
MegaCli -AdpCcSched -Dsbl|-Info|{-ModeConc | -ModeSeq [-ExcludeLD -LN|-L0,1,2]
   [-SetStartTime yyyymmdd hh ] [-SetDelay val ] } -aN|-a0,1,2|-aALL
MegaCli -AdpCcSched -SetStartTime yyyymmdd hh -aN|-a0,1,2|-aALL
MegaCli -AdpCcSched -SetDelay val  -aN|-a0,1,2|-aALL
MegaCli -FwTermLog -BBUoff|BBUoffTemp|BBUon|BBUGet|Dsply|Clear -aN|-a0,1,2|-aALL
MegaCli -AdpAlILog -aN|-a0,1,2|-aALL 
MegaCli -AdpDiag [val] -aN|-a0,1,2|-aALL
          val - Time in second.
MegaCli -AdpShutDown -aN|-a0,1,2|-aALL
MegaCli -PDList -aN|-a0,1,2|-aALL 
MegaCli -PDGetNum -aN|-a0,1,2|-aALL 
MegaCli -pdInfo -PhysDrv[E0:S0,E1:S1,...] -aN|-a0,1,2|-aALL
MegaCli -PDOnline  -PhysDrv[E0:S0,E1:S1,...] -aN|-a0,1,2|-aALL 
MegaCli -PDOffline -PhysDrv[E0:S0,E1:S1,...] -aN|-a0,1,2|-aALL 
MegaCli -PDMakeGood -PhysDrv[E0:S0,E1:S1,...] | [-Force] -aN|-a0,1,2|-aALL 
MegaCli -PDMakeJBOD -PhysDrv[E0:S0,E1:S1,...] -aN|-a0,1,2|-aALL 
MegaCli -PDHSP {-Set [-Dedicated [-ArrayN|-Array0,1,2...]] [-EnclAffinity] [-nonRevertible]} 
     |-Rmv -PhysDrv[E0:S0,E1:S1,...] -aN|-a0,1,2|-aALL 
MegaCli -PDRbld -Start|-Stop|-Suspend|-Resume|-ShowProg |-ProgDsply 
        -PhysDrv [E0:S0,E1:S1,...] -aN|-a0,1,2|-aALL  
MegaCli -PDClear -Start|-Stop|-ShowProg |-ProgDsply 
        -PhysDrv [E0:S0,E1:S1,...] -aN|-a0,1,2|-aALL  
MegaCli -PdLocate {[-start] | -stop} -physdrv[E0:S0,E1:S1,...] -aN|-a0,1,2|-aALL 
MegaCli -PdMarkMissing -physdrv[E0:S0,E1:S1,...] -aN|-a0,1,2|-aALL 
MegaCli -PdGetMissing -aN|-a0,1,2|-aALL 
MegaCli -PdReplaceMissing -physdrv[E0:S0] -arrayA, -rowB -aN 
MegaCli -PdPrpRmv [-UnDo] -physdrv[E0:S0] -aN|-a0,1,2|-aALL  
MegaCli -EncInfo -aN|-a0,1,2|-aALL 
MegaCli -EncStatus -aN|-a0,1,2|-aALL 
MegaCli -PhyInfo -phyM -aN|-a0,1,2|-aALL  
MegaCli -PhySetLinkSpeed -phyM -speed -aN|-a0,1,2|-aALL
MegaCli -PdFwDownload [offline][ForceActivate] {[-SataBridge] -PhysDrv[0:1] }|{-EncdevId[devId1]} -f <filename> -aN|-a0,1,2|-aALL 
MegaCli -LDInfo -Lx|-L0,1,2|-Lall -aN|-a0,1,2|-aALL 
MegaCli -LDSetProp  {-Name LdNamestring} | -RW|RO|Blocked|RemoveBlocked | WT|WB|ForcedWB [-Immediate] |RA|NORA|ADRA 
        | Cached|Direct | -EnDskCache|DisDskCache | CachedBadBBU|NoCachedBadBBU
        -Lx|-L0,1,2|-Lall -aN|-a0,1,2|-aALL 
MegaCli -LDSetPowerPolicy -Default| -Automatic| -None| -Maximum| -MaximumWithoutCaching 
        -Lx|-L0,1,2|-Lall -aN|-a0,1,2|-aALL 
MegaCli -LDGetProp  -Cache | -Access | -Name | -DskCache | -PSPolicy | Consistency -Lx|-L0,1,2|-LALL  
        -aN|-a0,1,2|-aALL 
MegaCli -LDInit {-Start [-full]}|-Abort|-ShowProg|-ProgDsply -Lx|-L0,1,2|-LALL -aN|-a0,1,2|-aALL 
MegaCli -LDCC {-Start [-force]}|-Abort|-Suspend|-Resume|-ShowProg|-ProgDsply -Lx|-L0,1,2|-LALL -aN|-a0,1,2|-aALL 
MegaCli -LDBI -Enbl|-Dsbl|-getSetting|-Abort|-Suspend|-Resume|-ShowProg|-ProgDsply -Lx|-L0,1,2|-LALL -aN|-a0,1,2|-aALL  
MegaCli -LDRecon {-Start -rX [{-Add | -Rmv} -Physdrv[E0:S0,...]]}|-ShowProg|-ProgDsply 
        -Lx -aN 
MegaCli -LdPdInfo -aN|-a0,1,2|-aALL 
MegaCli -LDGetNum -aN|-a0,1,2|-aALL 
MegaCli -LDBBMClr -Lx|-L0,1,2,...|-Lall -aN|-a0,1,2|-aALL 
MegaCli -getLdExpansionInfo -Lx|-L0,1,2|-Lall -aN|-a0,1,2|-aALL
MegaCli -LdExpansion -pN -dontExpandArray -Lx|-L0,1,2|-Lall -aN|-a0,1,2|-aALL 
MegaCli -GetBbtEntries -Lx|-L0,1,2|-Lall -aN|-a0,1,2|-aALL 
MegaCli -Cachecade -assign|-remove -Lx|-L0,1,2|-LALL -aN|-a0,1,2|-aALL
MegaCli -CfgLdAdd -rX[E0:S0,E1:S1,...] [WT|WB] [NORA|RA|ADRA] [Direct|Cached]
        [CachedBadBBU|NoCachedBadBBU] [-szXXX [-szYYY ...]]
        [-strpszM] [-Hsp[E0:S0,...]] [-AfterLdX] [-Force]|[Secure]  
                [-Default| -Automatic| -None| -Maximum| -MaximumWithoutCaching] [-Cache] -aN 
MegaCli -CfgCacheCadeAdd [-rX] -Physdrv[E0:S0,...] {-Name LdNamestring} [WT|WB|ForcedWB] [-assign -LX|L0,2,5..|LALL] -aN|-a0,1,2|-aALL 
MegaCli -CfgEachDskRaid0 [WT|WB] [NORA|RA|ADRA] [Direct|Cached] 
        [CachedBadBBU|NoCachedBadBBU] [-strpszM]|[Secure] [-Default| -Automatic| -None| -Maximum| -MaximumWithoutCaching] [-Cache] -aN|-a0,1,2|-aALL
MegaCli -CfgClr [-Force] -aN|-a0,1,2|-aALL 
MegaCli -CfgDsply -aN|-a0,1,2|-aALL 
MegaCli -CfgCacheCadeDsply -aN|-a0,1,2|-aALL 
MegaCli -CfgLdDel -LX|-L0,2,5...|-LALL [-Force] -aN|-a0,1,2|-aALL 
MegaCli -CfgCacheCadeDel -LX|-L0,2,5...|-LALL -aN|-a0,1,2|-aALL 
MegaCli -CfgFreeSpaceinfo -aN|-a0,1,2|-aALL 
MegaCli -CfgSpanAdd -r10 -Array0[E0:S0,E1:S1] -Array1[E0:S0,E1:S1] [-ArrayX[E0:S0,E1:S1] ...] 
        [WT|WB] [NORA|RA|ADRA] [Direct|Cached] [CachedBadBBU|NoCachedBadBBU]
        [-szXXX[-szYYY ...]][-strpszM][-AfterLdX][-Force]|[Secure] 
                [-Default| -Automatic| -None| -Maximum| -MaximumWithoutCaching] [-Cache] -aN 
MegaCli -CfgSpanAdd -r50 -Array0[E0:S0,E1:S1,E2:S2,...] -Array1[E0:S0,E1:S1,E2:S2,...] 
        [-ArrayX[E0:S0,E1:S1,E2:S2,...] ...] [WT|WB] [NORA|RA|ADRA] [Direct|Cached] 
        [CachedBadBBU|NoCachedBadBBU][-szXXX[-szYYY ...]][-strpszM][-AfterLdX][-Force]| 
RA|ADRA] 
        [Direct|Cached] [CachedBadBBU|NoCachedBadBBU] [-strpszM]
        [-HspCount XX [-HspType -Dedicated|-EnclAffinity|-nonRevertible]]| 
        [Secure] [-Default| -Automatic| -None| -Maximum| -MaximumWithoutCaching] [-Cache] -aN 
MegaCli -CfgSave -f filename -aN   
MegaCli -CfgRestore -f filename -aN   
MegaCli -CfgForeign -Scan | [-Passphrase sssssssssss] -aN|-a0,1,2|-aALL    
MegaCli -CfgForeign -Dsply [x] | [-Passphrase sssssssssss] -aN|-a0,1,2|-aALL    
MegaCli -CfgForeign -Preview [x] | [-Passphrase sssssssssss] -aN|-a0,1,2|-aALL    
MegaCli -CfgForeign -Import [x] | [-Passphrase sssssssssss] -aN|-a0,1,2|-aALL    
MegaCli -CfgForeign -Clear [x]|[-Passphrase sssssssssss] -aN|-a0,1,2|-aALL    
        x - index of foreign configurations. Optional. All by default. 
MegaCli -AdpEventLog -GetEventLogInfo -aN|-a0,1,2|-aALL 
MegaCli -AdpEventLog -GetEvents {-info -warning -critical -fatal} {-f <fileName>} -aN|-a0,1,2|-aALL
MegaCli -AdpEventLog -GetSinceShutdown {-info -warning -critical -fatal} {-f <fileName>} -aN|-a0,1,2|-aALL 
MegaCli -AdpEventLog -GetSinceReboot {-info -warning -critical -fatal} {-f <fileName>} -aN|-a0,1,2|-aALL 
MegaCli -AdpEventLog -IncludeDeleted {-info -warning -critical -fatal} {-f <fileName>} -aN|-a0,1,2|-aALL 
MegaCli -AdpEventLog -GetLatest n {-info -warning -critical -fatal} {-f <fileName>} -aN|-a0,1,2|-aALL 
MegaCli -AdpEventLog -GetCCIncon -f <fileName> -LX|-L0,2,5...|-LALL -aN|-a0,1,2|-aALL 
MegaCli -AdpEventLog -Clear -aN|-a0,1,2|-aALL 
MegaCli -AdpBbuCmd -aN|-a0,1,2|-aALL  
MegaCli -AdpBbuCmd -GetBbuStatus -aN|-a0,1,2|-aALL  
MegaCli -AdpBbuCmd -GetBbuCapacityInfo -aN|-a0,1,2|-aALL  
MegaCli -AdpBbuCmd -GetBbuDesignInfo -aN|-a0,1,2|-aALL  
MegaCli -AdpBbuCmd -GetBbuProperties -aN|-a0,1,2|-aALL  
MegaCli -AdpBbuCmd -BbuLearn -aN|-a0,1,2|-aALL  
MegaCli -AdpBbuCmd -BbuMfgSleep -aN|-a0,1,2|-aALL  
MegaCli -AdpBbuCmd -BbuMfgSeal -aN|-a0,1,2|-aALL  
MegaCli -AdpBbuCmd -SetBbuProperties -f <fileName> -aN|-a0,1,2|-aALL 
MegaCli -AdpBbuCmd -GetGGEEPData offset [Hexaddress] NumBytes n -aN|-a0,1,2|-aALL 
MegaCli -AdpFacDefSet -aN 
MegaCli -AdpFwFlash -f filename [-NoSigChk] [-NoVerChk] -aN|-a0,1,2|-aALL
MegaCli -AdpGetConnectorMode -ConnectorN|-Connector0,1|-ConnectorAll -aN|-a0,1,2|-aALL  
MegaCli -AdpSetConnectorMode -Internal|-External|-Auto -ConnectorN|-Connector0,1|-ConnectorAll -aN|-a0,1,2|-aALL  
MegaCli -PhyErrorCounters -aN|-a0,1,2|-aALL  
MegaCli -DirectPdMapping -Enbl|-Dsbl|-Dsply -aN|-a0,1,2|-aALL  
MegaCli -PDCpyBk -Start -PhysDrv[E0:S0,E1:S1] -aN|-a0,1,2|-aALL 
MegaCli -PDCpyBk -Stop|-Suspend|-Resume|-ShowProg|-ProgDsply -PhysDrv[E0:S0] -aN|-a0,1,2|-aALL 
MegaCli -PDInstantSecureErase -PhysDrv[E0:S0,E1:S1,...] | [-Force] -aN|-a0,1,2|-aALL 
MegaCli -PDInstantSecureErase -PhysDrv[E0:S0,E1:S1,...] | [-Force] -aN|-a0,1,2|-aALL 
MegaCli -AdpSetprop -enblPI 1 -aN|-a0,1,2|-aALL 
MegaCli -AdpGetprop -enblPI -aN|-a0,1,2|-aALL 
MegaCli -AdpSetprop -preventPiImport 1 -aN|-a0,1,2|-aALL 
MegaCli -AdpGetprop -preventPiImport -aN|-a0,1,2|-aALL 
MegaCli -CfgLdAdd rX[E0:S0,E1:S1,...] -enblPI -aN|-a0,1,2|-aALL 
MegaCli -CfgEachDskRaid0 -enblPI -aN|-a0,1,2|-aALL 
MegaCli -CfgSpanAdd -cfgspanadd -rX -array0[E0:S1,E1:S1.....] array1[E0:S1,E1:S1.....] -szxxx -enblPI -aN|-a0,1,2|-aALL
MegaCli -CfgAllFreeDrv -rX enblPI -aN|-a0,1,2|-aALL 
MegaCli -AdpSetVerify -f verify.txt -aN|-a0,1,2|-aALL 
MegaCli -LDMakeSecure -Lx|-L0,1,2,...|-Lall -aN|-a0,1,2|-aALL 
MegaCli -DeleteSecurityKey | [-Force] -aN 
MegaCli -CreateSecurityKey -Passphrase sssssssssss [-KeyID kkkkkkkkkkk] -aN 
MegaCli -CreateSecurityKey useEKMS -aN 
MegaCli -ChangeSecurityKey -OldPassphrase sssssssssss | -Passphrase sssssssssss |
          [-KeyID kkkkkkkkkkk] -aN
MegaCli -ChangeSecurityKey -Passphrase sssssssssss |
          [-KeyID kkkkkkkkkkk] -aN
MegaCli -ChangeSecurityKey useEKMS -oldPassphrase sssssssssss -aN
MegaCli -ChangeSecurityKey -useEKMS -aN
MegaCli -GetKeyID [-PhysDrv[E0:S0]] -aN 
MegaCli -SetKeyID -KeyID kkkkkkkkkkk -aN 
MegaCli -VerifySecurityKey -Passphrase sssssssssss -aN 
MegaCli -GetPreservedCacheList -aN|-a0,1,2|-aALL 
MegaCli -DiscardPreservedCache -Lx|-L0,1,2|-Lall -force -aN|-a0,1,2|-aALL 

       sssssssssss  - It must be between eight and thirty-two 
                      characters and contain at least one number, 
                      one lowercase letter, one uppercase 
                      letter and one non-alphanumeric character.
       kkkkkkkkkkk -  Must be less than 256 characters. 
MegaCli -ShowSummary [-f filename] -aN
MegaCli -ELF -GetSafeId -aN|-a0,1,2|-aALL
MegaCli -ELF -ControllerFeatures -aN|-a0,1,2|-aALL
MegaCli -ELF -Applykey key <-val> [Preview] -aN|-a0,1,2|-aALL
MegaCli -ELF -TransferToVault -aN|-a0,1,2|-aALL
MegaCli -ELF -DeactivateTrialKey -aN|-a0,1,2|-aALL
MegaCli -ELF -ReHostInfo -aN|-a0,1,2|-aALL
MegaCli -ELF -ReHostComplete -aN|-a0,1,2|-aALL
MegaCli -LDViewMirror -Lx|-L0,1,2,...|-Lall -aN|-a0,1,2|-aALL 
MegaCli -LDJoinMirror -DataSrc <val> [-force] -Lx|-L0,1,2,...|-Lall -aN|-a0,1,2|-aALL 
MegaCli -SecureErase 
        Start[
                Simple|
                [Normal   [ |ErasePattern ErasePatternA|ErasePattern ErasePatternA ErasePattern ErasePatternB]]|
                [Thorough [ |ErasePattern ErasePatternA|ErasePattern ErasePatternA ErasePattern ErasePatternB]]]
        | Stop
        | ShowProg
        | ProgDsply 
        [-PhysDrv [E0:S0,E1:S1,...] | -Lx|-L0,1,2|-LALL] -aN|-a0,1,2|-aALL
MegaCli -Version -Cli|-Ctrl|-Driver|-Pd   -aN|-a0,1,2|-aALL
MegaCli -Perfmon {-start -interval <val>} | {stop} | {-getresults -f <Filename>} -aN 

    Note: The directly connected drives can be specified as [:S] 
    Wildcard '?' can be used to specify the enclosure ID for the drive in the 
       only enclosure without direct connected device or the direct connected 
       drives with no enclosure in the system.
    Note:[-aALL] option assumes that the parameters specified are valid 
       for all the Adapters. 
    The following options may be given at the end of any command above: 
       [-Silent] [-AppLogFile filename] [-NoLog] [-page[N]] 
       [-] is optional. 
       N - Number of lines per page.
faq/sysadmin/megacli.txt · Dernière modification: 2020/08/25 17:58 (modification externe)