Différences

Ci-dessous, les différences entre deux révisions de la page.

--- faq:sysadmin:megacli [2019/01/07 10:50] – créée ltaulell
+++ faq:sysadmin:megacli [2023/01/18 10:10] (Version actuelle) – supprimée ltaulell
@@ Ligne 1: / Ligne 1: @@
-======MegaCli======
-http://hwraid.le-vert.net/wiki/LSIMegaRAIDSAS
-http://wiki.hetzner.de/index.php/LSI_RAID_Controller/en
-http://tools.rapidsoft.de/perc/perc-cheat-sheet.html
-http://perso.ens-lyon.fr/kevin.reverchon/doku.php?id=start:sysadmin:zfs_dell
-http://www.inquisitor.ru/doc/einarc/
-Sur les R510dataX, pour maniper sur les controleur raid, à chaud.
-  * lister les disques et leurs état :
-<code>
-./MegaCli -PdList -aALL | grep alert
-./MegaCli -pdlist -a0 | /usr/xpg4/bin/grep -e '^Enclosure Device ID:' -e '^Slot Number:' -e 'alert'
-</code>
-==== Caches, Battery + WriteBack ====
-  * activation du ReadCache (Adapter)
-<code>
-./MegaCli -LDSetProp -Cached -LAll -aAll
-</code>
-  * activation du DiskCache (Disk)
-<code>
-./MegaCli -LDSetProp EnDskCache -LAll -aAll
-</code>
-  * activation du AdaptiveReadAhead (Adapter)
-<code>
-./MegaCli -LDSetProp ADRA -LALL -aALL
-</code>
-  * état des batteries
-<code>
-./MegaCli -AdpBbuCmd -GetBbuStatus -a0 | /usr/xpg4/bin/grep -e '^isSOHGood' -e '^Charger Status' -e '^Remaining Capacity'
-./MegaCli -AdpBbuCmd -GetBbuStatus -a1 | /usr/xpg4/bin/grep -e '^isSOHGood' -e '^Charger Status' -e '^Remaining Capacity'
-</code>
-Si tout est good :
-  * Activation du WB
-<code>
-./MegaCli -LDSetProp WB -LALL -aALL
-</code>
-  * mais désactivation automatique si la batterie devient bad
-<code>
-./MegaCli -LDSetProp NoCachedBadBBU -LALL -aALL
-</code>
-  * si on se fout de l'état des batteries (ZFS is COW)
-<code>
-./MegaCli -LDSetProp CachedBadBBU -LALL -aALL
-</code>
-  * activation du JBOD
-:!: ne fonctionne **pas** sur les **vraies** cartes raid H700/710, H800/810, devrait fonctionner sur les H200/H210, H300/H310
-<code>
-MegaCli -AdpSetProp -EnableJBOD -1 -aALL
-</code>
-====Remplacer un disque HS====
-**sur R510dataX**
-<code>zpool scrub <pool></code>
-    * Repérer le disque fautif
-<code>
-./MegaCli -pdlist -a0 | /usr/xpg4/bin/grep -e '^Enclosure Device ID:' -e '^Slot Number:' -e 'alert'
-./MegaCli -PDInfo -PhysDrv\[32:11\] -a0
-</code>
-    * Éjecter le disque fautif
-<code>
-./MegaCli -PdPrpRmv -PhysDrv\[32:11\] -a0
-./MegaCli -PDOffLine -PhysDrv\[32:11\] -a0
-</code>
-    * **échanger physiquement les disques**
-    * effacer la config VD ou foreign du nouveau disque (si besoin)
-<code>
-#./MegaCli -PDMakeGood -PhysDrv \[32:11\] -a0 # si Unconfigured(bad)
-./MegaCli -CfgForeign -Scan -a0
-./MegaCli -CfgForeign -Clear -a0
-#./MegaCli -PDClear -Start -PhysDrv\[32:11\] -a0 # si dans un raid > 0
-</code>
-    * trouver et purger le preserved cache
-<code>
-./MegaCli -AdpAllInfo -a0 -nolog | grep Preserved
-./MegaCli -GetPreservedCacheList -a0
-./MegaCli -DiscardPreservedCache -L13 -a0
-</code>
-    * créer un nouveau VD (raid0) avec le nouveau Physical Disk (Write Through)
-<code>
-./MegaCli -CfgLdAdd -r0 '[32:11]' -a0
-Adapter 0: Created VD 13
-Adapter 0: Configured the Adapter!!
-Exit Code: 0x00
-</code>
-    * créer un nouveau disque d'accès direct (H200,H310,H730/830)
-<code>
-./MegaCli -PDMakeJBOD -PhysDrv[32:1] -a0
-</code>
-    * remettre les configs du VD au propre (cache, WB, readahead, etc)
-<code>
-./MegaCli -LDSetProp -Cached -LAll -aAll
-./MegaCli -LDSetProp EnDskCache -LAll -aAll
-./MegaCli -LDSetProp ADRA -LALL -aALL
-./MegaCli -LDSetProp WB -LALL -aALL
-./MegaCli -LDSetProp NoCachedBadBBU -LALL -aALL
-</code>
-  * prévenir zfs
-<code>
-zpool status
-zpool replace data c0t6d0
-zpool status
-</code>
-Un resilver du disque doit démarrer automatiquement.
-<note warning>Voir aussi [[cmd:zfs#remplacer_un_disque_systeme]]</note>
-Ref : http://docs.oracle.com/cd/E19253-01/819-5461/gbcet/index.html
-====MegaCli -help====
-<code>
-MegaCli -v
-MegaCli -help|-h|?
-MegaCli -adpCount
-MegaCli -AdpSetProp {CacheFlushInterval -val} | { RebuildRate -val}
-    | {PatrolReadRate -val} | {BgiRate -val} | {CCRate -val}
-    | {ReconRate -val} | {SpinupDriveCount -val} | {SpinupDelay -val}
-    | {CoercionMode -val} | {ClusterEnable -val} | {PredFailPollInterval -val}
-    | {BatWarnDsbl -val} | {EccBucketSize -val} | {EccBucketLeakRate -val}
-    | {AbortCCOnError -val} | AlarmEnbl | AlarmDsbl | AlarmSilence
-    | {SMARTCpyBkEnbl -val} | {SSDSMARTCpyBkEnbl -val} | NCQEnbl | NCQDsbl
-    | {MaintainPdFailHistoryEnbl -val} | {RstrHotSpareOnInsert -val}
-    | {DisableOCR -val} | {BootWithPinnedCache -val}
-    | AutoEnhancedImportEnbl | AutoEnhancedImportDsbl
-    | {EnblSpinDownUnConfigDrvs -val}|{UseDiskActivityforLocate -val} -aN|-a0,1,2|-aALL
-    | {ExposeEnclDevicesEnbl -val} | {SpinDownTime -val}
-    | {SpinUpEncDrvCnt -val} | {SpinUpEncDelay -val} | {Perfmode -val} -aN|-a0,1,2|-aALL
-</code>
-<code>
-MegaCli -AdpSetProp -AutoDetectBackPlaneDsbl -val -aN|-a0,1,2|-aALL
-       val - 0=Enable Auto Detect of SGPIO and i2c SEP.
-=Disable Auto Detect of SGPIO.
-=Disable Auto Detect of i2c SEP.
-=Disable Auto Detect of SGPIO and i2c SEP.
-MegaCli -AdpSetProp -CopyBackDsbl -val -aN|-a0,1,2|-aALL
-       val - 0=Enable Copyback.
-=Disable Copyback.
-MegaCli -AdpSetProp -EnableJBOD -val -aN|-a0,1,2|-aALL
-       val - 0=Disable JBOD mode.
-=Enable JBOD mode.
-MegaCli -AdpSetProp -DsblCacheBypass -val -aN|-a0,1,2|-aALL
-       val - 0=Enable Cache Bypass.
-=Disable Cache Bypass.
-MegaCli -AdpSetProp -LoadBalanceMode -val -aN|-a0,1,2|-aALL
-       val - 0=Auto Load balance mode.
-=Disable Load balance mode.
-MegaCli -AdpSetProp -UseFDEOnlyEncrypt -val -aN|-a0,1,2|-aALL
-       val - 0=FDE and controller encryption (if HW supports) is allowed.
-=Only support FDE encryption, disallow controller encryption.
-MegaCli -AdpSetProp -PrCorrectUncfgdAreas -val -aN|-a0,1,2|-aALL
-       val - 0= Correcting Media error during PR is disabled.
-=Correcting Media error during PR is allowed.
-MegaCli -AdpSetProp -DsblSpinDownHSP -val -aN|-a0,1,2|-aALL
-       val - 0= Spinning down the Hot Spare is enabled.
-=Spinning down the Hot Spare is disabled.
-MegaCli -AdpSetProp -DefaultLdPSPolicy -Automatic| -None | -Maximum| -MaximumWithoutCaching -aN|-a0,1,2|-aALL
-MegaCli -AdpSetProp -DisableLdPS -interval n1 -time n2 -aN|-a0,1,2|-aALL
-       where n1 is the number of hours beginning at time n2
-</code>
-<code>
-MegaCli -AdpSetProp -ENABLEEGHSP -val -aN|-a0,1,2|-aALL
-           val - 0= Disabled Emergency GHSP.
-= Enabled Emergency GHSP.
-MegaCli -AdpSetProp -ENABLEEUG -val -aN|-a0,1,2|-aALL
-           val - 0= Disabled Emergency UG as Spare.
-= Enabled Emergency UG as Spare.
-MegaCli -AdpSetProp -ENABLEESMARTER -val -aN|-a0,1,2|-aALL
-           val - 0= Disabled Emergancy Spare as Smarter.
-= Enabled Emergancy Spare as Smarter.
-MegaCli -AdpSetProp -DPMenable -val -aN|-a0,1,2|-aALL
-       val - 0=Disable Drive Performance Monitoring .
-=Enable Drive Performance Monitoring.
-MegaCli -AdpSetProp -SupportSSDPatrolRead -val -aN|-a0,1,2|-aALL
-       val - 0=Disable Patrol read for SSD drives .
-=Enable Patrol read for SSD drives.
-MegaCli -AdpGetProp CacheFlushInterval | RebuildRate | PatrolReadRate
-    | BgiRate | CCRate | ReconRate | SpinupDriveCount | SpinupDelay
-    | CoercionMode | ClusterEnable | PredFailPollInterval | BatWarnDsbl
-    | EccBucketSize | EccBucketLeakRate | EccBucketCount | AbortCCOnError
-    | AlarmDsply | SMARTCpyBkEnbl | SSDSMARTCpyBkEnbl | NCQDsply
-    | MaintainPdFailHistoryEnbl | RstrHotSpareOnInsert
-    | EnblSpinDownUnConfigDrvs  | DisableOCR
-    | BootWithPinnedCache | AutoEnhancedImportDsply | AutoDetectBackPlaneDsbl
-    | CopyBackDsbl | LoadBalanceMode | UseFDEOnlyEncrypt | WBSupport | EnableJBOD
-    | DsblCacheBypass | ExposeEnclDevicesEnbl | SpinDownTime | PrCorrectUncfgdAreas
-    | UseDiskActivityforLocate | ENABLEEGHSP | ENABLEEUG | ENABLEESMARTER | Perfmode | -DPMenable -aN|-a0,1,2|-aALL
-    | DefaultLdPSPolicy | DisableLdPsInterval | DisableLdPsTime | SpinUpEncDrvCnt
-    | SpinUpEncDelay | PrCorrectUncfgdAreas
-    | DsblSpinDownHSP | SupportSSDPatrolRead -aN|-a0,1,2|-aALL
-</code>
-<code>
-MegaCli -AdpAllInfo -aN|-a0,1,2|-aALL
-MegaCli -AdpGetTime -aN|-a0,1,2|-aALL
-MegaCli -AdpSetTime yyyymmdd hh:mm:ss -aN
-MegaCli -AdpSetVerify -f fileName -aN|-a0,1,2|-aALL
-MegaCli -BBUMfgSet -f filename -aN|-a0,1,2|-aALL
-MegaCli -AdpBIOS -Enbl |-Dsbl | -SOE | -BE | EnblAutoSelectBootLd | DsblAutoSelectBootLd | -Dsply -aN|-a0,1,2|-aALL
-MegaCli -AdpBootDrive {-Set {-Lx | -physdrv[E0:S0]}}|-Get -aN|-a0,1,2|-aALL
-MegaCli -AdpAutoRbld -Enbl|-Dsbl|-Dsply -aN|-a0,1,2|-aALL
-MegaCli -AdpCacheFlush -aN|-a0,1,2|-aALL
-MegaCli -AdpPR -Dsbl|EnblAuto|EnblMan|Start|Suspend|Resume|Stop|Info|SSDPatrolReadEnbl |SSDPatrolReadDsbl
-         |{SetDelay Val}|{-SetStartTime yyyymmdd hh}|{maxConcurrentPD Val} -aN|-a0,1,2|-aALL
-MegaCli -AdpCcSched -Dsbl|-Info|{-ModeConc | -ModeSeq [-ExcludeLD -LN|-L0,1,2]
-   [-SetStartTime yyyymmdd hh ] [-SetDelay val ] } -aN|-a0,1,2|-aALL
-MegaCli -AdpCcSched -SetStartTime yyyymmdd hh -aN|-a0,1,2|-aALL
-MegaCli -AdpCcSched -SetDelay val  -aN|-a0,1,2|-aALL
-MegaCli -FwTermLog -BBUoff|BBUoffTemp|BBUon|BBUGet|Dsply|Clear -aN|-a0,1,2|-aALL
-MegaCli -AdpAlILog -aN|-a0,1,2|-aALL
-MegaCli -AdpDiag [val] -aN|-a0,1,2|-aALL
-          val - Time in second.
-MegaCli -AdpShutDown -aN|-a0,1,2|-aALL
-</code>
-<code>
-MegaCli -PDList -aN|-a0,1,2|-aALL
-MegaCli -PDGetNum -aN|-a0,1,2|-aALL
-MegaCli -pdInfo -PhysDrv[E0:S0,E1:S1,...] -aN|-a0,1,2|-aALL
-MegaCli -PDOnline  -PhysDrv[E0:S0,E1:S1,...] -aN|-a0,1,2|-aALL
-MegaCli -PDOffline -PhysDrv[E0:S0,E1:S1,...] -aN|-a0,1,2|-aALL
-MegaCli -PDMakeGood -PhysDrv[E0:S0,E1:S1,...] | [-Force] -aN|-a0,1,2|-aALL
-MegaCli -PDMakeJBOD -PhysDrv[E0:S0,E1:S1,...] -aN|-a0,1,2|-aALL
-MegaCli -PDHSP {-Set [-Dedicated [-ArrayN|-Array0,1,2...]] [-EnclAffinity] [-nonRevertible]}
-     |-Rmv -PhysDrv[E0:S0,E1:S1,...] -aN|-a0,1,2|-aALL
-MegaCli -PDRbld -Start|-Stop|-Suspend|-Resume|-ShowProg |-ProgDsply
-        -PhysDrv [E0:S0,E1:S1,...] -aN|-a0,1,2|-aALL
-MegaCli -PDClear -Start|-Stop|-ShowProg |-ProgDsply
-        -PhysDrv [E0:S0,E1:S1,...] -aN|-a0,1,2|-aALL
-MegaCli -PdLocate {[-start] | -stop} -physdrv[E0:S0,E1:S1,...] -aN|-a0,1,2|-aALL
-MegaCli -PdMarkMissing -physdrv[E0:S0,E1:S1,...] -aN|-a0,1,2|-aALL
-MegaCli -PdGetMissing -aN|-a0,1,2|-aALL
-MegaCli -PdReplaceMissing -physdrv[E0:S0] -arrayA, -rowB -aN
-MegaCli -PdPrpRmv [-UnDo] -physdrv[E0:S0] -aN|-a0,1,2|-aALL
-MegaCli -EncInfo -aN|-a0,1,2|-aALL
-MegaCli -EncStatus -aN|-a0,1,2|-aALL
-MegaCli -PhyInfo -phyM -aN|-a0,1,2|-aALL
-MegaCli -PhySetLinkSpeed -phyM -speed -aN|-a0,1,2|-aALL
-MegaCli -PdFwDownload [offline][ForceActivate] {[-SataBridge] -PhysDrv[0:1] }|{-EncdevId[devId1]} -f <filename> -aN|-a0,1,2|-aALL
-MegaCli -LDInfo -Lx|-L0,1,2|-Lall -aN|-a0,1,2|-aALL
-MegaCli -LDSetProp  {-Name LdNamestring} | -RW|RO|Blocked|RemoveBlocked | WT|WB|ForcedWB [-Immediate] |RA|NORA|ADRA
-        | Cached|Direct | -EnDskCache|DisDskCache | CachedBadBBU|NoCachedBadBBU
-        -Lx|-L0,1,2|-Lall -aN|-a0,1,2|-aALL
-MegaCli -LDSetPowerPolicy -Default| -Automatic| -None| -Maximum| -MaximumWithoutCaching
-        -Lx|-L0,1,2|-Lall -aN|-a0,1,2|-aALL
-MegaCli -LDGetProp  -Cache | -Access | -Name | -DskCache | -PSPolicy | Consistency -Lx|-L0,1,2|-LALL
-        -aN|-a0,1,2|-aALL
-MegaCli -LDInit {-Start [-full]}|-Abort|-ShowProg|-ProgDsply -Lx|-L0,1,2|-LALL -aN|-a0,1,2|-aALL
-MegaCli -LDCC {-Start [-force]}|-Abort|-Suspend|-Resume|-ShowProg|-ProgDsply -Lx|-L0,1,2|-LALL -aN|-a0,1,2|-aALL
-MegaCli -LDBI -Enbl|-Dsbl|-getSetting|-Abort|-Suspend|-Resume|-ShowProg|-ProgDsply -Lx|-L0,1,2|-LALL -aN|-a0,1,2|-aALL
-MegaCli -LDRecon {-Start -rX [{-Add | -Rmv} -Physdrv[E0:S0,...]]}|-ShowProg|-ProgDsply
-        -Lx -aN
-</code>
-<code>
-MegaCli -LdPdInfo -aN|-a0,1,2|-aALL
-MegaCli -LDGetNum -aN|-a0,1,2|-aALL
-MegaCli -LDBBMClr -Lx|-L0,1,2,...|-Lall -aN|-a0,1,2|-aALL
-MegaCli -getLdExpansionInfo -Lx|-L0,1,2|-Lall -aN|-a0,1,2|-aALL
-MegaCli -LdExpansion -pN -dontExpandArray -Lx|-L0,1,2|-Lall -aN|-a0,1,2|-aALL
-MegaCli -GetBbtEntries -Lx|-L0,1,2|-Lall -aN|-a0,1,2|-aALL
-MegaCli -Cachecade -assign|-remove -Lx|-L0,1,2|-LALL -aN|-a0,1,2|-aALL
-MegaCli -CfgLdAdd -rX[E0:S0,E1:S1,...] [WT|WB] [NORA|RA|ADRA] [Direct|Cached]
-        [CachedBadBBU|NoCachedBadBBU] [-szXXX [-szYYY ...]]
-        [-strpszM] [-Hsp[E0:S0,...]] [-AfterLdX] [-Force]|[Secure]
-                [-Default| -Automatic| -None| -Maximum| -MaximumWithoutCaching] [-Cache] -aN
-MegaCli -CfgCacheCadeAdd [-rX] -Physdrv[E0:S0,...] {-Name LdNamestring} [WT|WB|ForcedWB] [-assign -LX|L0,2,5..|LALL] -aN|-a0,1,2|-aALL
-MegaCli -CfgEachDskRaid0 [WT|WB] [NORA|RA|ADRA] [Direct|Cached]
-        [CachedBadBBU|NoCachedBadBBU] [-strpszM]|[Secure] [-Default| -Automatic| -None| -Maximum| -MaximumWithoutCaching] [-Cache] -aN|-a0,1,2|-aALL
-MegaCli -CfgClr [-Force] -aN|-a0,1,2|-aALL
-MegaCli -CfgDsply -aN|-a0,1,2|-aALL
-MegaCli -CfgCacheCadeDsply -aN|-a0,1,2|-aALL
-MegaCli -CfgLdDel -LX|-L0,2,5...|-LALL [-Force] -aN|-a0,1,2|-aALL
-MegaCli -CfgCacheCadeDel -LX|-L0,2,5...|-LALL -aN|-a0,1,2|-aALL
-MegaCli -CfgFreeSpaceinfo -aN|-a0,1,2|-aALL
-MegaCli -CfgSpanAdd -r10 -Array0[E0:S0,E1:S1] -Array1[E0:S0,E1:S1] [-ArrayX[E0:S0,E1:S1] ...]
-        [WT|WB] [NORA|RA|ADRA] [Direct|Cached] [CachedBadBBU|NoCachedBadBBU]
-        [-szXXX[-szYYY ...]][-strpszM][-AfterLdX][-Force]|[Secure]
-                [-Default| -Automatic| -None| -Maximum| -MaximumWithoutCaching] [-Cache] -aN
-MegaCli -CfgSpanAdd -r50 -Array0[E0:S0,E1:S1,E2:S2,...] -Array1[E0:S0,E1:S1,E2:S2,...]
-        [-ArrayX[E0:S0,E1:S1,E2:S2,...] ...] [WT|WB] [NORA|RA|ADRA] [Direct|Cached]
-        [CachedBadBBU|NoCachedBadBBU][-szXXX[-szYYY ...]][-strpszM][-AfterLdX][-Force]|
-RA|ADRA]
-        [Direct|Cached] [CachedBadBBU|NoCachedBadBBU] [-strpszM]
-        [-HspCount XX [-HspType -Dedicated|-EnclAffinity|-nonRevertible]]|
-        [Secure] [-Default| -Automatic| -None| -Maximum| -MaximumWithoutCaching] [-Cache] -aN
-</code>
-<code>
-MegaCli -CfgSave -f filename -aN
-MegaCli -CfgRestore -f filename -aN
-MegaCli -CfgForeign -Scan | [-Passphrase sssssssssss] -aN|-a0,1,2|-aALL
-MegaCli -CfgForeign -Dsply [x] | [-Passphrase sssssssssss] -aN|-a0,1,2|-aALL
-MegaCli -CfgForeign -Preview [x] | [-Passphrase sssssssssss] -aN|-a0,1,2|-aALL
-MegaCli -CfgForeign -Import [x] | [-Passphrase sssssssssss] -aN|-a0,1,2|-aALL
-MegaCli -CfgForeign -Clear [x]|[-Passphrase sssssssssss] -aN|-a0,1,2|-aALL
-        x - index of foreign configurations. Optional. All by default.
-MegaCli -AdpEventLog -GetEventLogInfo -aN|-a0,1,2|-aALL
-MegaCli -AdpEventLog -GetEvents {-info -warning -critical -fatal} {-f <fileName>} -aN|-a0,1,2|-aALL
-MegaCli -AdpEventLog -GetSinceShutdown {-info -warning -critical -fatal} {-f <fileName>} -aN|-a0,1,2|-aALL
-MegaCli -AdpEventLog -GetSinceReboot {-info -warning -critical -fatal} {-f <fileName>} -aN|-a0,1,2|-aALL
-MegaCli -AdpEventLog -IncludeDeleted {-info -warning -critical -fatal} {-f <fileName>} -aN|-a0,1,2|-aALL
-MegaCli -AdpEventLog -GetLatest n {-info -warning -critical -fatal} {-f <fileName>} -aN|-a0,1,2|-aALL
-MegaCli -AdpEventLog -GetCCIncon -f <fileName> -LX|-L0,2,5...|-LALL -aN|-a0,1,2|-aALL
-MegaCli -AdpEventLog -Clear -aN|-a0,1,2|-aALL
-MegaCli -AdpBbuCmd -aN|-a0,1,2|-aALL
-MegaCli -AdpBbuCmd -GetBbuStatus -aN|-a0,1,2|-aALL
-MegaCli -AdpBbuCmd -GetBbuCapacityInfo -aN|-a0,1,2|-aALL
-MegaCli -AdpBbuCmd -GetBbuDesignInfo -aN|-a0,1,2|-aALL
-MegaCli -AdpBbuCmd -GetBbuProperties -aN|-a0,1,2|-aALL
-MegaCli -AdpBbuCmd -BbuLearn -aN|-a0,1,2|-aALL
-MegaCli -AdpBbuCmd -BbuMfgSleep -aN|-a0,1,2|-aALL
-MegaCli -AdpBbuCmd -BbuMfgSeal -aN|-a0,1,2|-aALL
-MegaCli -AdpBbuCmd -SetBbuProperties -f <fileName> -aN|-a0,1,2|-aALL
-MegaCli -AdpBbuCmd -GetGGEEPData offset [Hexaddress] NumBytes n -aN|-a0,1,2|-aALL
-MegaCli -AdpFacDefSet -aN
-MegaCli -AdpFwFlash -f filename [-NoSigChk] [-NoVerChk] -aN|-a0,1,2|-aALL
-</code>
-<code>
-MegaCli -AdpGetConnectorMode -ConnectorN|-Connector0,1|-ConnectorAll -aN|-a0,1,2|-aALL
-MegaCli -AdpSetConnectorMode -Internal|-External|-Auto -ConnectorN|-Connector0,1|-ConnectorAll -aN|-a0,1,2|-aALL
-MegaCli -PhyErrorCounters -aN|-a0,1,2|-aALL
-MegaCli -DirectPdMapping -Enbl|-Dsbl|-Dsply -aN|-a0,1,2|-aALL
-MegaCli -PDCpyBk -Start -PhysDrv[E0:S0,E1:S1] -aN|-a0,1,2|-aALL
-MegaCli -PDCpyBk -Stop|-Suspend|-Resume|-ShowProg|-ProgDsply -PhysDrv[E0:S0] -aN|-a0,1,2|-aALL
-MegaCli -PDInstantSecureErase -PhysDrv[E0:S0,E1:S1,...] | [-Force] -aN|-a0,1,2|-aALL
-MegaCli -PDInstantSecureErase -PhysDrv[E0:S0,E1:S1,...] | [-Force] -aN|-a0,1,2|-aALL
-MegaCli -AdpSetprop -enblPI 1 -aN|-a0,1,2|-aALL
-MegaCli -AdpGetprop -enblPI -aN|-a0,1,2|-aALL
-MegaCli -AdpSetprop -preventPiImport 1 -aN|-a0,1,2|-aALL
-MegaCli -AdpGetprop -preventPiImport -aN|-a0,1,2|-aALL
-MegaCli -CfgLdAdd rX[E0:S0,E1:S1,...] -enblPI -aN|-a0,1,2|-aALL
-MegaCli -CfgEachDskRaid0 -enblPI -aN|-a0,1,2|-aALL
-MegaCli -CfgSpanAdd -cfgspanadd -rX -array0[E0:S1,E1:S1.....] array1[E0:S1,E1:S1.....] -szxxx -enblPI -aN|-a0,1,2|-aALL
-MegaCli -CfgAllFreeDrv -rX enblPI -aN|-a0,1,2|-aALL
-MegaCli -AdpSetVerify -f verify.txt -aN|-a0,1,2|-aALL
-MegaCli -LDMakeSecure -Lx|-L0,1,2,...|-Lall -aN|-a0,1,2|-aALL
-MegaCli -DeleteSecurityKey | [-Force] -aN
-MegaCli -CreateSecurityKey -Passphrase sssssssssss [-KeyID kkkkkkkkkkk] -aN
-MegaCli -CreateSecurityKey useEKMS -aN
-MegaCli -ChangeSecurityKey -OldPassphrase sssssssssss | -Passphrase sssssssssss |
-          [-KeyID kkkkkkkkkkk] -aN
-MegaCli -ChangeSecurityKey -Passphrase sssssssssss |
-          [-KeyID kkkkkkkkkkk] -aN
-MegaCli -ChangeSecurityKey useEKMS -oldPassphrase sssssssssss -aN
-MegaCli -ChangeSecurityKey -useEKMS -aN
-MegaCli -GetKeyID [-PhysDrv[E0:S0]] -aN
-MegaCli -SetKeyID -KeyID kkkkkkkkkkk -aN
-MegaCli -VerifySecurityKey -Passphrase sssssssssss -aN
-MegaCli -GetPreservedCacheList -aN|-a0,1,2|-aALL
-</code>
-<code>
-MegaCli -DiscardPreservedCache -Lx|-L0,1,2|-Lall -force -aN|-a0,1,2|-aALL
-       sssssssssss  - It must be between eight and thirty-two
-                      characters and contain at least one number,
-                      one lowercase letter, one uppercase
-                      letter and one non-alphanumeric character.
-       kkkkkkkkkkk -  Must be less than 256 characters.
-MegaCli -ShowSummary [-f filename] -aN
-MegaCli -ELF -GetSafeId -aN|-a0,1,2|-aALL
-MegaCli -ELF -ControllerFeatures -aN|-a0,1,2|-aALL
-MegaCli -ELF -Applykey key <-val> [Preview] -aN|-a0,1,2|-aALL
-MegaCli -ELF -TransferToVault -aN|-a0,1,2|-aALL
-MegaCli -ELF -DeactivateTrialKey -aN|-a0,1,2|-aALL
-MegaCli -ELF -ReHostInfo -aN|-a0,1,2|-aALL
-MegaCli -ELF -ReHostComplete -aN|-a0,1,2|-aALL
-MegaCli -LDViewMirror -Lx|-L0,1,2,...|-Lall -aN|-a0,1,2|-aALL
-MegaCli -LDJoinMirror -DataSrc <val> [-force] -Lx|-L0,1,2,...|-Lall -aN|-a0,1,2|-aALL
-MegaCli -SecureErase
-        Start[
-                Simple|
-                [Normal   [ |ErasePattern ErasePatternA|ErasePattern ErasePatternA ErasePattern ErasePatternB]]|
-                [Thorough [ |ErasePattern ErasePatternA|ErasePattern ErasePatternA ErasePattern ErasePatternB]]]
-        | Stop
-        | ShowProg
-        | ProgDsply
-        [-PhysDrv [E0:S0,E1:S1,...] | -Lx|-L0,1,2|-LALL] -aN|-a0,1,2|-aALL
-MegaCli -Version -Cli|-Ctrl|-Driver|-Pd   -aN|-a0,1,2|-aALL
-MegaCli -Perfmon {-start -interval <val>} | {stop} | {-getresults -f <Filename>} -aN
-    Note: The directly connected drives can be specified as [:S]
-    Wildcard '?' can be used to specify the enclosure ID for the drive in the
-       only enclosure without direct connected device or the direct connected
-       drives with no enclosure in the system.
-    Note:[-aALL] option assumes that the parameters specified are valid
-       for all the Adapters.
-    The following options may be given at the end of any command above:
-       [-Silent] [-AppLogFile filename] [-NoLog] [-page[N]]
-       [-] is optional.
-       N - Number of lines per page.
-</code>

faq/sysadmin/megacli.1546858224.txt.gz · Dernière modification : 2020/08/25 15:58 (modification externe)

Rechercher

Translations

Piste :

Vous êtes ici : accueil » faq » sysadmin » megacli